So, i set up a WLAN using VLAN 10 and configured a VLAN on the edgerouter lite but when my client connects to the WLAN, it doesnt seem to be getting any ip address. Router config is as follows:firewall { all-ping enable broadcast-ping disable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name VLAN10_IN { default-action accept description "" rule 1 { action drop description "DROP access to 192.168.1.x" destination { address 192.168.1.0/24 } log disable protocol all } } name VLAN10_LOCAL { default-action accept description "" rule 10 { action accept description "ALLOW access to VLAN10 DNS" destination { port 53 } log disable protocol tcp_udp } rule 20 { action drop description "DROP access to 192.168.10.1" destination { address 192.168.10.1 } log disable protocol all } } name WAN_IN { default-action drop description "WAN to internal" rule 10 { action accept description "Allow established/related" state { established enable related enable } } rule 20 { action drop description "Drop invalid state" state { invalid enable } } } name WAN_LOCAL { default-action drop description "WAN to router" rule 10 { action accept description "Allow established/related" state { established enable related enable } } rule 20 { action drop description "Drop invalid state" state { invalid enable } } } options { mss-clamp { mss 1412 } } receive-redirects disable send-redirects enable source-validation disable syn-cookies enable}interfaces { ethernet eth0 { address 192.168.1.1/24 description Local duplex auto speed auto vif 10 { address 192.168.10.1/24 description Guest firewall { in { name VLAN10_IN } local { name VLAN10_LOCAL } } mtu 1500 } } ethernet eth1 { description "Internet (PPPoE)" duplex auto pppoe 0 { default-route auto firewall { in { name WAN_IN } local { name WAN_LOCAL } } mtu 1492 name-server auto password **************** user-id Bigpipe } speed auto } ethernet eth2 { address 192.168.2.1/24 description "Local 2" duplex auto speed auto } loopback lo { }}port-forward { auto-firewall enable hairpin-nat enable lan-interface eth0 wan-interface eth1}service { dhcp-server { disabled false hostfile-update disable shared-network-name GUEST { authoritative disable subnet 192.168.10.0/24 { default-router 192.168.10.1 dns-server 208.67.222.222 dns-server 208.67.220.220 lease 86400 start 192.168.10.10 { stop 192.168.10.20 } } } shared-network-name LAN1 { authoritative disable subnet 192.168.1.0/24 { default-router 192.168.1.1 dns-server 192.168.1.1 lease 86400 start 192.168.1.21 { stop 192.168.1.240 } } } shared-network-name LAN2 { authoritative disable subnet 192.168.2.0/24 { default-router 192.168.2.1 dns-server 192.168.2.1 lease 86400 start 192.168.2.21 { stop 192.168.2.240 } } } use-dnsmasq disable } dns { forwarding { cache-size 150 listen-on eth0 listen-on eth2 name-server 192.168.1.10 } } gui { http-port 80 https-port 443 older-ciphers enable } nat { rule 5010 { outbound-interface pppoe0 type masquerade } } ssh { port 22 protocol-version v2 }}system { host-name ubnt login { user ubnt { authentication { encrypted-password **************** } level admin } } ntp { server 0.ubnt.pool.ntp.org { } server 1.ubnt.pool.ntp.org { } server 2.ubnt.pool.ntp.org { } server 3.ubnt.pool.ntp.org { } } syslog { global { facility all { level notice } facility protocols { level debug } } } time-zone UTC}On the E400, i set up a WLAN with VLAN 10 and in the network configuration, under Ethernet ports, enabled 'Trunk Multiple VLANS' with VLAN 10 added in scope
↧